PREVIOUS PAGE 1568 INDEX B&H INDEX MANUALS INDEX NEXT PAGE

FRONT REEL SUPPLY ARM ASSEMBLY for all 1500 & 2500 series projectors (not for 500 series)          

 

014948

REEL ARM ASSEMBLY, Front (NOTE C)

REF

 

1

30882

SCREW, Swedge type, special

2

 

2

42217

COVER, Front reel arm

1

 

3

34859

WASHER, Shim

2

 

4

44309

SCREW, Special

1

 

5

014615

SPINDLE ASSEMBLY, Feed

1

 

5A

765777

RING, Retaining, external, 0.250 inch ID

1

 

5B

36764

SETSCREW, Fluted socket cup pt, 6/32 by 1/16”

2

 

5C

44271

GEAR, Face, lower

1

 

5D

31359

WASHER, Flat

1

 

5E

014614

SPINDLE ASSEMBLY, Feed (NOTE A)

1

 

5F

31115

WASHER, Spacer (NOTE A)

1

 

6

700672

WASHER, Shim

1

 

7

31038

RING, Retaining, external, 0.156 inch ID . .

1

 

8

36764

SETSCREW, Fluted socket cup pt, 6/32 by 3/16”

1

 

8A

36765

SETSCREW, Fluted socket cup pt., 6/32 by 1/8”

1

 

9

45577

GEAR, Face, upper (NOTE B)

1

 

9A

45578

SLEEVE, Plastic (NOTE B)

1

 

10

44598

SPRING, Torsion (early models) (NOTE B)

1

 

10

45579

SPRING, Torsion (current models) (NOTE B)

1

 

11

765777

RING, Retaining, external, 0.250 inch ID

2

 

12

31017

WASHER, Thrust

1

 

13

700672

WASHER, Spacer

1

 

14

44403

SHAFT, Front reel arm (all models to Serial No. 2314000)

1

 

14

48901

SHAFT, Front reel arm ("B" models Serial No. 2314001 and up)

1

BEGJ

15

31245

RING, Retaining, grip type, 0.187 inch ID

1

 

16

33385

GEAR, Spur, upper

1

 

17

31241

CLIP, Gear retaining

2

 

18

31243

WASHER, Flat

1

 

19

31239

GEAR, Spur, lower

1

 

20

44407

SHAFT, Gear

1

 

21

31236

BEARING, Nylon

2

 

22

014616

ARM AND BEARING ASSEMBLY, Front reel

1

 

 

NOTE A:  The feed spindle assembly (item 5E) used in earlier models has been superseded by spindle assembly P/N 014614, which is slightly longer (see inset, Figure 6).There fore, when replacing the spindle assembly, spacer washer P/N 31115 (item 5F) must be assembled to the spindle shaft.

 NOTE B:  The upper face gear (item 9) used in earlier models has been superseded by face gear P/N 45577 with separate plastic sleeve P/N 45578 (item 9A). Therefore, when replacing the face gear, the plastic sleeve must be included and a new torsion spring P/N 45579 (item 10) must be installed. Torsion spring P/N 45598 is still available for replacement on earlier models.

 NOTE C:  Front reel arm P/N 014517, used on projectors to Serial No. 2314000, is no longer available. If the complete arm assembly must be replaced use arm assembly P/N 014948 plus take-up clutch assembly P/N 014949 (item 314) and spur gear P/N 46534 (item 315).

          

PREVIOUS PAGE 1568 INDEX B&H INDEX MANUALS INDEX NEXT PAGE

B&H 16mm Parts list updated 05/20/06